| General Summary|
It is anticipated that this position will be for Second Shift, Monday through Friday. Based on operational needs, other shifts may be considered.
Job duties include but are not limited to:
Cleaning sewer and storm drains
Repair/replace corroded and cracked drain, waste, and vent piping.
Repair/replace leaks on water distribution piping, pumps, waste systems, bath and kitchen faucets, fixtures, and drains.
Soldering, welding, crimping of water and related heat distribution piping.
Operating power tools, soldering and welding equipment, drain cleaning machines, threading equipment, hand tools, and plumbing equipment.
Laying out, cutting, and fitting material for soldering, crimping, or welding; repairing valves and pumps; install gas related equipment, pipe, and fittings; cutting and threading pipes; caulking and packing lead joints, installing or replacing all trade related pipe and fittings; replacing seals in water closets; maintain water filter systems; assist with maintenance of neutralization systems; insulating pipes, installing heat tracing wires for piping.
Maintain domestic hot and cold water systems.
Maintain waste and storm water ejection systems.
Testing and maintenance of University fire hydrants. Report deficiencies to Facilities Operations and Services.
Respond to emergency calls such as water leaks, gas odors, clogged drains, no hot water. Reschedule daily work load to accommodate the emergency calls.
Diagnose and repair problems of unknown sources such as water leaks from waste, water, and heat piping; unidentified odors; non-functioning equipment; loss of utility services, frozen pipes, etc.
Clean/replace plumbing related filter systems for reverse osmosis and deionized water in labs.
Repair backflow prevention devices for lab and kitchen equipment.
Repair/replace special waste piping for lab equipment.
Clear clogged drains for kitchen equipment and indirect wastes.
Service kitchen gas equipment.
Inspects buildings to determine need for repairs.
Notes hazardous conditions and establishes work priorities based on safety requirements and the operational needs of the facility.
Reviews and interprets blueprints, GIS mapping, sketches, instructions or layouts to understand construction work to be done. Makes recommendations.
Schedule installations, maintenance, and/or repair work by conferring with supervisors and other department personnel to determine location of equipment and appropriate time to complete the project.
Communicates and interacts with the State Plumbing Inspector, processes permit applications, complies with Mass State Plumbing Code.
Perform related duties such as erecting scaffolding, riggings, and/or ladders; laying out drop cloths; shop cleaning; shop repair work; job related paperwork; fabricating miscellaneous metal products; sharpening and repairing various tools; cleaning and maintaining a service vehicle; cleaning tools and equipment; cleaning work spaces after job completion. Reviews technical data to keep current of developments in the plumbing field.
Completes all work orders and related paperwork as directed.
Trains employees on the job.
Reports unsafe or disorderly conditions to Facilities Operations and Services
Preventative Maintenance on systems such as:
Backflow prevention systems
Storm drain and catch basin systems
Commercial kitchen grease trap systems
Hot and cold domestic water systems
Booster and circulating pumps
Roof drains, floor drains, and area drains
Winterization of freeze susceptible equipment
Cleaning/jetting of waste and storm main drains
All building faucets and fixtures
Other duties as assigned
Plumbers are exposed to the hazards of sanitary waste systems; climb and work from ladders and scaffolds; work in confined spaces; drive for job related travel; may work varied hours, exposed to the elements and unconditioned spaces.
Involves emergency recall and overtime work
Able to work evenings and weekends.
-Massachusetts Journeyman or Master Plumbing License
-Knowledge of state and local plumbing codes
-Ability to understand, explain and apply the laws, rules, and regulations governing assigned unit activities
-Ability to interpret and apply laws, rules, and regulations concerning plumbing practices
-Knowledge of the principles and theory of plumbing and steam fitting
-Knowledge of the types and use of small hand tools used in plumbing practices such as wrenches, hammers, pliers, taps, dies, etc.
-Knowledge of the types and uses of hand held power tools and equipment such as propress, power saws, power drills, power hammers, torches, gauges, etc.
-Knowledge of the types and uses of equipment including testing equipment used in plumbing work
-Knowledge of safety practices and procedures followed in plumbing
-Knowledge of inspection techniques used in the plumbing trade
-Ability to lift and carry heavy objects
-Ability to follow oral and written instructions
-Ability to write clearly and concisely
-Ability to maintain accurate records
-Ability to establish and maintain harmonious working relationships
-Ability to read and interpret documents such as plumbing plans, schematics, drawings, etc.
-Ability to make decision and act quickly in emergency situations
-Manual dexterity and aptitude
-Ability to climb and work from ladders and scaffolds, work in confined spaces
-Ability to detect and locate causes of plumbing failure or breakdown
-The ability to work effectively with diverse groups
-Minimum of 3 years' experience, installing, servicing, or inspecting plumbing systems, gas distribution systems, and boiler components
-Possess a current and valid driver's license
-Demonstrated willingness & ability to be on essential personnel list for facility related emergencies and University Closings due to weather
-5 years' experience as a Massachusetts licensed plumber.
Demonstrated willingness to be on essential personnel list for facility related emergencies and University Closings due to weather
-Ability to operate air and hydraulic lifts
-Similar institution experience
-A general knowledge of steam and HVAC systems
-Ability to diagnose boiler controls such as gas valves, relays, aquastats, pressuretrols, power burners, etc.
-Ability to use electrical testing meters